Techniques

Stained Glass Tools and Materials

The tools and materials a beginner needs for stained glass, from glass and cutters to solder, flux, came and safety gear, with a practical starter list.

On this page
  1. Set up a workspace first
  2. Cutting tools
  3. Pattern and layout tools
  4. Glass
  5. Copper foil or lead came
  6. Soldering supplies
  7. Grinding supplies
  8. Finishing supplies
  9. Safety gear
  10. What to buy first

Set up a workspace first

Stained glass needs a flat, sturdy table, good light, and a place to keep glass off the floor. Soldering needs ventilation, so choose a room with a window or a fan, and plan for a fume extractor if you can. A vacuum is essential for shards. Keep the room warm enough for comfortable work, because cold glass scores and breaks less predictably.

Protect the table with a board or a cutting mat, and keep a surface for laying out your pattern and pieces.

Cutting tools

  • Glass cutter. An oil-fed cutter is the usual choice for stained glass. It keeps the wheel lubricated.
  • Cutting oil. Keep it in the cutter’s reservoir and wipe the wheel before every cut.
  • Running pliers and grozing pliers. Running pliers break a score along a straight line. Grozing pliers nibble waste glass away, especially on curves.
  • Cutting mat or board. A padded surface protects the glass and the table.
  • Metal ruler and steel square. Use the ruler as a straightedge and the square to check corners.
  • Fine marker or grease pencil. Use it to trace cut lines onto the glass.

For how to use these tools, read how to score and cut glass for stained glass.

Pattern and layout tools

Your pattern can be printed, hand-drawn, or traced onto transparency sheets. Transparency sheets let you lay a pattern under the glass and see the pieces clearly. A layout board, usually wood, holds the pattern while you work. Layout blocks, which are small blocks placed along the frame, help keep the panel square while you solder. Check your corners with a square.

Glass

Glass is usually the largest cost in stained glass, so buy carefully. Glass comes in many types, including transparent, opalescent, streaky, and textured. Each one changes how light passes through the panel. See types of stained glass for how they differ.

For practice, buy scrap sheet glass or inexpensive practice pieces. Local stained glass studios, scrap bins, and secondhand sellers can be good sources. Avoid bottle glass for cutting practice, because it is curved and uneven. For a design that depends on color, hold samples up to the light where the finished panel will hang.

Copper foil or lead came

Copper foil is adhesive-backed tape used in the Tiffany method, named for Louis Comfort Tiffany’s studios. Look for foil that is copper on both faces, so the solder bonds on both sides. The most common width for stained glass is 7/32 inch (about 5.5 mm). You will also need a foil burnisher to press the foil down smoothly onto the edges.

Lead came comes in H-shaped and U-shaped channels. Choose a came width that matches the thickness of your glass. You will need a fid, a tool for pressing the came flanges down and working them into place. Lead came also needs a cement or putty to make a finished window weatherproof.

Zinc came is a stiffer border metal that works well for framing panels and giving straight, clean lines.

For help choosing between them, read copper foil vs lead came.

Soldering supplies

  • Soldering iron. Many glass artists use a higher-wattage, temperature-controlled iron, rather than a small craft iron. Check the manufacturer’s range for the solder you buy.
  • Iron stand. A stand keeps the hot tip safe when you are not using it.
  • Tip cleaner. A damp sponge or brass wool keeps the tip clean and working well.
  • Solder. Most stained glass work uses 60/40 solder, a mix of tin and lead. Lead-free options are available, but they are harder to work with. Check the label before you buy.
  • Flux. Choose a flux made for stained glass, in paste, liquid, or gel form. Avoid acid flux, which corrodes the joints.
  • Solder fume extractor or fan. Pull fumes away from your face while you solder.

For steps, see how to solder stained glass.

Grinding supplies

  • Electric glass grinder. Use a grinder made for glass, and check that the bits fit the grinder before you buy them.
  • Grinding bits. Diamond or carborundum bits remove glass. Replace them when they wear down, because worn bits grind unevenly.
  • Water or coolant. Keep the bit wet while grinding. This lowers dust and keeps the bit cool.
  • Splash guard. A simple shield behind the grinder keeps water and glass dust off the bench.
  • Hand grinding stone. A small carborundum stone is useful for quick touch-ups.

For steps, see how to grind stained glass edges smooth.

Finishing supplies

  • Patina. Black or copper patina changes the color of the solder. Follow the label closely.
  • Flux remover or soap and water. Remove flux residue after soldering.
  • Fine steel wool or a brass scrubber. Clean the solder before patina.
  • Finishing wax. A thin coat protects the patina and gives a polished look.
  • Rags, cotton swabs, and brushes. Use them to apply patina and wax.

For steps, see how to patina stained glass.

Safety gear

  • Safety glasses. Wear them for cutting, grinding, and soldering.
  • Gloves. Use cut-resistant or thick gloves when handling glass, and rubber gloves for patina.
  • Fume control. A fume extractor, a fan, or a mask helps when ventilation is limited.
  • First-aid kit. Keep bandages nearby. Cuts from glass edges are common.

Lead came and lead-based solder contain lead. Wash your hands after working, and do not eat or drink at the bench. For more, see is stained glass safe? lead, solder fumes and glass dust.

What to buy first

For a first project, you need:

  • A glass cutter, cutting oil, and running and grozing pliers
  • A straightedge, a square, and a marker
  • Copper foil and a burnisher, or lead came and a fid
  • A soldering iron, a stand, flux, and solder
  • A grinder and bits, or a hand stone
  • Safety glasses, gloves, and a vacuum

You can wait on items that help but are not essential at the start, such as a foiling tool, a laminator for patterns, a cutting machine for templates, a saw for framing, or specialty pliers. Borrow tools from a class where you can. Buy the best tools you can afford for cutting and soldering, since those skills affect every piece. For a budget overview, see how much it costs to start stained glass as a hobby.

The complete guide to techniques

Stained Glass Techniques: A Beginner's Overview
Read the guide

Keep exploring

Guides from other topics

All topics →

Stained Glass Project Ideas

Stained glass project ideas for every skill level, from beginner suncatchers to lampshades and window panels, using copper foil or lead came.

Projects 5 min read