Techniques

How to Solder Stained Glass: Tinning, Flux and Making Joints

How to solder stained glass: set up your iron, apply flux, tin the copper foil, tack the joints, bead the seams, and clean off the flux safely.

On this page
  1. What soldering does
  2. Tools and materials
  3. Choosing flux, and why not acid flux
  4. Prepare the piece
  5. Tinning the copper foil
  6. Tacking the joints
  7. Beading the seams
  8. Soldering the edges and the back
  9. Cleaning off the flux
  10. Common mistakes and fixes
  11. Safety

What soldering does

Solder bonds the copper foil on each piece to the foil on its neighbors, and it makes the whole panel rigid. In lead came work, solder joins the came at each intersection. The bead of solder also shows, so a neat, even seam is part of the finished look.

Tools and materials

  • A temperature-controlled soldering iron. Many glass artists use a higher-wattage iron than a small craft iron. Set the temperature within the range the solder maker recommends.
  • An iron stand and a tip cleaner. A damp sponge or brass wool keeps the tip clean. A clean tip transfers heat better.
  • Solder. Most stained glass work uses 60/40 solder, a tin and lead mix. Lead-free solder is available but melts at a higher temperature and handles differently.
  • Stained glass flux. Use a flux made for stained glass or copper foil, in paste, liquid, or gel form.
  • A fume extractor or fan. Solder smoke should be pulled away from your face.
  • Safety glasses. Wear them whenever you solder.

For more on choosing these, see stained glass tools and materials.

Choosing flux, and why not acid flux

Flux cleans the metal and helps solder flow smoothly into the seam. Use a flux labeled for stained glass. Avoid acid flux, the type used in plumbing. Acid flux corrodes metal, and it can keep damaging joints over time.

Apply flux just before you solder. Brush or dab it onto the foil along the seams you plan to solder. Flux that dries out will not clean the metal as well.

Prepare the piece

Before you solder, check the basics:

  • Glass at room temperature. Sudden heat or cold can crack glass. If the piece has been in a cold room, let it warm up first.
  • Foil burnished down. Press the foil firmly onto the edges so there are no lifting corners or gaps.
  • A clean surface. Fingerprints and oils keep the solder from bonding. Wipe the foil with a clean cloth.
  • A stable board. Pin or brace the pieces so they do not shift as you work. Layout blocks and a square help keep the panel straight.

Tinning the copper foil

Tinning means coating the copper foil with a thin layer of solder before you join the pieces. It helps the bead bond and makes the seams easier to solder later.

  1. Apply flux to the foil edge.
  2. Touch the hot iron to the foil and let it warm.
  3. Feed a little solder onto the tip so it melts onto the foil.
  4. Spread a thin, even coat along the edge. Avoid thick blobs, and do not let solder run between separate seams. That is called bridging.

Tacking the joints

Tacking holds the pieces in place before you bead the full seams. Put small dabs of solder on the key joints and intersections first. Hold the iron on the joint until the solder flows, then lift the iron away. Tacking locks the shape, so you can remove pins or braces safely.

Beading the seams

A bead is the raised line of solder along a seam.

  1. Hold the iron against the seam and let it heat the foil.
  2. Feed solder into the joint as you move steadily along the line.
  3. Keep the iron moving at a steady pace, and do not drag it back and forth.
  4. When the solder flows and spreads, lift the iron straight up. This avoids sharp points.
  5. Re-flux the seam if the solder drags or hesitates.

Move the iron and solder in one direction, and avoid painting or dragging the iron across the joint. Dragging can leave a weak, pasty joint with rough spikes.

Soldering the edges and the back

Attach hanging loops or jump rings before you finish the outside edge. Then tin the outer edges of the foil. Let the glass cool between passes, since heat can crack it if you move too quickly. When the front is done, turn the panel over and solder the seams on the back.

Cleaning off the flux

Wait until the solder has cooled, then wash the flux off with warm water and soap or a dedicated flux cleaner. Leftover flux can dull the finish, and some fluxes keep damaging the joints if they are not removed. Dry the panel completely before you apply patina or wax. For those steps, see how to patina stained glass.

Common mistakes and fixes

  • Cold joints. The solder does not flow into the seam, or looks grainy. The iron may not be hot enough, or the joint was not heated. Re-flux and let the joint heat.
  • Pasty joints. Moving the iron around during soldering prevents the solder from setting into a strong joint. Hold steady until the solder flows, then lift.
  • Overheating. Solder spreads, looks dull, and can weaken the joint. Keep the iron on the seam only as long as needed.
  • Bridging. Solder runs between seams that should be separate. Remove the excess with the iron tip, and use a little flux.
  • Spikes. Sharp points are left where the iron was lifted too quickly. Lift the iron straight up when the seam flows.
  • Cracked glass. Usually caused by heat applied too quickly, or by glass that was too cold. Heat and cool more slowly.

Safety

  • Fumes. Work in a ventilated space, and use a fume extractor if you can. Keep your face away from the smoke.
  • Lead solder. Wash your hands after soldering, and do not eat or drink at the bench. See is stained glass safe? lead, solder fumes and glass dust.
  • Burns. Keep the iron in its stand when it is not in use. Hot solder can splash.
  • Cords. Keep the power cord clear of the bench and away from water.

For how soldering fits with the other joining methods, read copper foil vs lead came. For the steps before soldering, see how to grind stained glass edges smooth.

The complete guide to techniques

Stained Glass Techniques: A Beginner's Overview
Read the guide

Keep exploring

Guides from other topics

All topics →

Stained Glass Project Ideas

Stained glass project ideas for every skill level, from beginner suncatchers to lampshades and window panels, using copper foil or lead came.

Projects 5 min read