Why grind the edges
Cut glass has sharp, rough edges. Grinding does three jobs. It removes the sharpest edges, so the pieces are safer to handle. It makes each piece match the pattern, so the panel goes together without gaps. It also gives the copper foil or lead came a clean edge to seat against.
Grinding is usually done after scoring and breaking, and before foiling or leading. For how to cut the pieces first, see how to score and cut glass for stained glass.
Grinder types and bits
- Electric grinder with a grinding bit. This is the usual tool. Diamond or carborundum bits remove glass. Check that the bit fits your grinder before you buy it.
- Hand grinding stone. A small carborundum stone is useful for quick touch-ups on small pieces.
- Replace worn bits. A worn bit grinds slowly and unevenly, and it is more likely to chip the glass.
Setup: water, coolant, and a guard
Keep the bit wet while you grind. Water or grinder coolant keeps dust down, cools the bit, and helps prevent it from seizing. Set up a splash shield behind the grinder so water and glass slurry do not spread across the bench.
Wear goggles or safety glasses. Before you start, plug in the grinder and check that it runs smoothly with no wobble.
Grinding technique
- Hold the glass firmly with both hands. Keep your fingers clear of the bit at all times.
- Use light pressure. Let the bit remove the glass. Pressing hard causes chips and cracks.
- Move the glass steadily along the bit. Do not hold it in one spot, since that wears a dip into the edge.
- Grind up to the pattern line. Remove the rough edge, then stop at the line.
- Check the fit after each pass. Hold the piece against the pattern and look for gaps or high spots.
Keep the edge straight, or follow the curve shown in the pattern. Work in short passes, and check often.
Fit each piece against the pattern
Test-fit each piece on the pattern before you foil or lead it. The piece should sit inside its lines with no gaps. If a piece is too large, grind it down a little at a time. If it is too small, cut a new piece, because glass cannot be added back.
Grind before foiling, and the outside edge last
Grind the pieces before you apply foil. Grinding after foiling can tear or lift the foil, and the water and slurry can loosen its adhesive.
The outside edge of a finished panel is a special case. Some artists leave the outer edge until the panel is assembled, so the outside is ground last, after the pattern is complete. Check your method before you start, since this changes the order of the steps.
Keep the bit in good shape
- Check the bit’s surface regularly. A clogged or glazed bit grinds unevenly.
- Replace the bit when it is worn. Worn bits take longer and are more likely to chip glass.
- Use bits that match your grinder. A mismatched bit can wobble or fail.
Common mistakes
- Grinding too much. Pieces end up too small, and gaps show when they are assembled.
- Chips or cracks. Caused by too much pressure, a worn bit, or glass that is very cold or very hot.
- Grinding dry. Dry grinding creates dust and heat. Keep the bit wet.
- Uneven edges. Usually caused by holding the glass at an angle or staying in one spot too long.
- Sharp edges after grinding. The edge may still be sharp. Check gently with a fingertip, and handle the piece carefully.
Clean up glass dust and slurry
Rinse each piece under running water and dry it fully before you foil or lead it. Glass slurry, the wet mix of glass dust and water, dries into a film on the bench if you leave it. Wipe it up with a damp cloth. Keep slurry out of drains, since it can clog them, and dispose of it as your local rules allow.
Safety
- Eyes. Wear goggles or safety glasses for the whole job.
- Hands. Keep fingers clear of the bit. Hold the glass by its sides, not over the bit.
- Dust. Wet grinding cuts dust, but do not breathe in glass dust. Clean up with a damp cloth rather than a dry broom. For more on glass dust and other hazards, see is stained glass safe? lead, solder fumes and glass dust.
- Water and power. Keep water away from the plug, the cord, and the switch.
For the next step, see copper foil vs lead came to choose the method, and how to solder stained glass once the pieces are joined.