History

Medieval Stained Glass Techniques and Glass Painting

How medieval glassmakers colored, painted, fired, cut and leaded their windows, from pot metal and flashed glass to grisaille, silver stain and cames.

On this page
  1. Medieval glass: the raw material
  2. Pot metal and flashed glass
  3. Making sheet glass: crown and cylinder methods
  4. Designing with a cartoon
  5. Cutting with a hot iron and grozing iron
  6. Painting with grisaille
  7. Silver stain
  8. Firing the paint
  9. Assembling the panel with lead came
  10. Cementing and bracing
  11. The basic tools, then and now
  12. What modern makers still borrow
  13. Starting out with the craft today
  14. Where to see medieval techniques

Medieval glass: the raw material

Medieval glass was made by melting sand, which is mostly silica, with an alkali flux. The flux was usually potash, made from plant ash, which lowered the melting point. Lime was often added to make the glass more stable. The glass was not clear in the modern sense. It had streaks, bubbles, and slight color, and those irregularities are part of its character.

Color came from metal oxides stirred into the molten glass. Cobalt gave deep blue, manganese gave purple, and copper gave green and, under controlled conditions, red. Glassmakers had less control over color than modern makers, so a single batch could vary.

Pot metal and flashed glass

“Pot metal” glass is colored all the way through. The color is part of the batch, so a cut edge shows the same hue as the face.

Red was harder to get right. Thick red glass often looked nearly black, so glassmakers used flashing. A thin layer of colored glass was fused onto a clear or lighter sheet. The result kept its brightness, and the thin color layer gave makers a second kind of glass to work with.

Making sheet glass: crown and cylinder methods

Medieval glassmakers blew a bubble of glass and then flattened it into a sheet. There were two main methods.

  • Crown method: The bubble was transferred to an iron rod called a pontil and spun quickly. Centrifugal force opened it into a flat disc. The disc had a thicker center, the bullseye, where the pontil had been attached.
  • Cylinder (muff) method: The bubble was blown into a long cylinder, which was then cut open, reheated, and flattened into a sheet.

Both methods gave sheets of uneven thickness. Glaziers worked around those variations.

Designing with a cartoon

Medieval glazing started from a full-size drawing called a cartoon. It was drawn on a white-washed board, parchment, or paper, and showed the shape of each piece, the color, the lead lines, and any supporting bars. The cartoon was the master plan for the whole panel.

Cutting with a hot iron and grozing iron

Glaziers traced the cartoon onto the sheet and cut it apart with simple tools. A hot iron could be used to score and crack the glass along a line. Edges were trimmed with a grozing iron, which had a notched head that nibbled small bites from the glass. The work was slow and needed a steady hand, and it is one reason why medieval pieces have such varied edges.

Painting with grisaille

Small pieces of colored glass could not show fine detail. Faces, folds of cloth, and the edges of leaves were painted on the glass instead. The paint was usually grisaille, a dark, monochrome mixture of ground glass, iron oxide or copper, and a binder such as gum or water. Painters applied it in layers to make shadows and lines, then removed some of it to show highlights.

Silver stain

Silver stain came into use in the early 14th century. Silver compounds were painted onto the glass, and when fired they turned yellow to amber. This allowed warm golds on hair, halos, and borders, without needing a separate yellow glass piece for each detail. It was one of the most important new tools of late medieval glass.

Firing the paint

After painting, the glass was fired in a kiln. The heat melted the powdered glass in the paint and fused it into the surface. Without firing, the paint would wear away or wash off. Firing was a key step, and a badly fired piece could lose its detail over time.

Assembling the panel with lead came

Glass pieces were joined with lead came. Came is an H-shaped lead strip with grooves on each side. The edges of each glass piece slide into the grooves, and the cames are laid over the cartoon. Joints where came meets came were soldered, so the whole panel became one rigid piece. Lead is soft and flexible, which lets a panel flex slightly, but it also means it can sag over centuries.

Cementing and bracing

Once the panel was assembled, cement was pushed into the joints between the lead and the glass. The cement made the panel watertight and stiffer. Large windows needed more support. Iron bars were fixed across the panels, and iron armatures were set into the stonework to hold the whole window against wind.

The basic tools, then and now

Medieval workshops relied on a small set of tools: a cartoon board, a hot iron for scoring, a grozing iron for trimming, lead came with a knife to fit and cut it, a soldering iron, brushes for painting, and a kiln.

A modern starter kit serves the same purposes. A glass cutter with a wheel scores the glass, grozing pliers trim the edges, and a soldering iron with solder and flux joins lead came. Copper foil replaces lead for many small or curved pieces. A pattern and a flat, level board complete the setup. Eye protection and good ventilation matter, because cutting glass sends out fine shards and soldering lead produces fumes. Wash your hands after handling lead.

What modern makers still borrow

Lead came is still used on large panels, and the cartoon remains the basis for planning. Copper foil, a method popularized in the 19th century and closely linked to Tiffany-style work, is an alternative for small and curved pieces. It is useful for learners because it allows fine curves that are hard to achieve with lead. For the later history of these methods, read the Victorian revival.

Starting out with the craft today

Beginners usually start with a small, simple pattern, a few colors of glass, and one method, either lead came or copper foil. Practice cutting on scrap glass before using good sheets. A simple suncatcher is a common first project, and it uses the same steps medieval glaziers followed: plan from a cartoon, cut each piece, fit the pieces together, and then join them with lead or foil. Take it slowly. Cutting and fitting are the skills that take the longest to build.

Where to see medieval techniques

The best way to see these techniques is in person. Look for the thick lead lines, the flashing on red glass, the grisaille shading on faces and folds, and the warm yellows from silver stain. Lighting matters, so a window seen from inside, with daylight behind it, will show the color most clearly. For the setting these windows were made for, see Gothic stained glass. For how the earliest windows came to be, see when stained glass was invented.

The complete guide to history

A Brief History of Stained Glass and Glass Painting
Read the guide

Keep exploring

Guides from other topics

All topics →

Stained Glass Project Ideas

Stained glass project ideas for every skill level, from beginner suncatchers to lampshades and window panels, using copper foil or lead came.

Projects 5 min read