Projects

How to Photograph Stained Glass Art

Learn how to photograph stained glass art with backlight, a tripod, and no flash, plus glare control, camera settings, and framing tips for sharp color.

On this page
  1. How to best photograph stained glass
  2. Control reflections and glare
  3. Camera settings
  4. Square the camera to the panel
  5. Framing: the 2/3 rule
  6. What camera do you need?
  7. What “photographs on glass” means
  8. Editing and file tips
  9. Photos for selling
  10. Common mistakes

Stained glass is hard to photograph because the light that makes it glow is also what causes glare, hot spots, and uneven exposure. A few choices, mostly about light, make a large difference. You do not need expensive equipment to get clear, accurate photos for a portfolio or an online listing.

How to best photograph stained glass

The most important rule is to light the glass from behind. Stained glass is made to be seen with light passing through it. A photo taken with the light in front of the piece shows a flat, dull surface. Good options include:

  • Daylight through a window. Hang or stand the panel in front of a window, ideally on an overcast day, when the light is soft and even. Direct sun creates bright spots and sharp shadows.
  • A diffused light panel. A flat, evenly lit panel placed behind the glass gives the same light for every shot.
  • Indoor lamps. Room lights in front of the piece create reflections. Use them only as a last resort.

Control reflections and glare

Reflections are the main problem. Glass reflects whatever is in front of it, including you and your camera.

  • Turn off room lights that are not behind the glass.
  • Shoot in a dim room, so the light coming through the glass is brighter than the reflections of the room.
  • Wear dark clothing, and keep your own shadow out of the frame.
  • A polarizing filter reduces reflections on the glass surface. It also cuts the total amount of light, so the exposure may need to be longer.

Camera settings

  • Use a tripod or rest the camera on a stable surface. This keeps the shot sharp and makes it easier to keep the frame straight.
  • Use a low ISO, such as the camera’s base setting, to keep noise down.
  • Turn off the flash. Flash bounces off the glass and creates hot spots and reflections.
  • Use manual or aperture-priority mode, then check the result on screen. Backlit glass can fool the meter, so take a few shots at different exposures and compare them on a large screen.
  • Shoot in RAW if your camera supports it, so you can adjust exposure and white balance later.
  • Use a timer or remote shutter to avoid shake when you press the button.

Square the camera to the panel

Place the camera straight on, centered on the piece, at about the height of the middle of the panel. Shooting at an angle tilts the piece and warps its edges, which matters when you want an accurate record. Zooming in slightly, rather than standing close with a wide lens, also reduces distortion. Use a level or the grid overlay on your camera screen to keep the frame straight.

Framing: the 2/3 rule

The “2/3 rule” is usually used for one of two things: the rule of thirds, which places key elements along lines that divide the frame into thirds, or placing the horizon at two-thirds of the way up the frame. Neither matters much for a flat panel, where the goal is to show the whole design. For most stained glass photos, center the piece with an even margin on every side so the edges are clear. Use the thirds grid for detail shots, such as a corner, a cluster of pieces, or a close-up of the solder lines.

What camera do you need?

A camera with manual controls works best, such as a mirrorless or DSLR camera. A recent smartphone with a manual or pro mode can also produce good results for most listings. Lighting and a tripod matter more than the camera body.

What “photographs on glass” means

People searching for “photographs on glass” usually mean one of two historical processes, not stained glass. An ambrotype is a photographic image on glass with a dark backing behind it. A glass plate negative is an image on a glass plate that was used to make prints. If you are looking for stained glass photography, the rest of this guide applies.

Editing and file tips

  • Crop to the piece with a small border.
  • Adjust exposure and white balance carefully. Keep the colors close to what you see in person, and check them against the piece if you can.
  • Keep an unedited original.
  • Export one version sized for the web and one at a larger size for print.

Photos for selling

If you plan to sell, take two versions of each piece: one backlit to show the color, and one front-lit to show the solder lines and the finish (see how to patina stained glass). Add a close-up of the joints and a size reference, such as a ruler or a common object. Use the same settings for a whole series so the photos match. For pricing and product ideas, see what stained glass items sell best.

Common mistakes

  • Using flash.
  • Shooting in direct sun, which creates hot spots.
  • Leaving room lights on in front of the glass.
  • Photographing at an angle.
  • Cropping so tightly that the edges are cut off.

For more project ideas, see stained glass project ideas.

The complete guide to projects

Stained Glass Project Ideas
Read the guide

Keep exploring

Guides from other topics

All topics →